Allied Telesis Switch 48W User Manual

Rapier 48w Switch  
Installation and Safety Guide  
Rapier 48w  
Rapier 48w-B  
 
Rapier 48w Switch  
Installation and Safety Guide  
Rapier 48w  
Rapier 48w-B  
Download the complete document set from  
 
Rapier 48w Switch  
Rapier 48w Switch Installation and Safety Guide  
Document Number 613-000757 REV C  
© 2007-2011 Allied Telesis, Inc. All rights reserved. No part of this publication  
may be reproduced without prior written permission from Allied Telesis, Inc.  
Allied Telesis, Inc. reserves the right to change specifications and other  
information in this document without prior written notice. The information  
provided herein is subject to change without notice. In no event shall Allied  
Telesis, Inc. be liable for any incidental, special, indirect, or consequential  
damages whatsoever, including but not limited to lost profits, arising out of or  
related to this manual or the information contained herein, even if Allied Telesis,  
Inc. has been advised of, known, or should have known, the possibility of such  
damages.  
All company names, logos, and product designs that are trademarks or  
registered trademarks are the property of their respective owners.  
2
 
Contents  
Veiligheid ........................................................................................................................... 28  
Sécurité ............................................................................................................................. 30  
Turvallisuus ....................................................................................................................... 32  
Norme di Sicurezza ........................................................................................................ 33  
Sikkerhet ........................................................................................................................... 35  
Segurança .......................................................................................................................... 37  
Seguridad .......................................................................................................................... 39  
Säkerhet ............................................................................................................................ 41  
Telecommunications Interfaces ................................................................................... 42  
3
 
Rapier 48w Switch  
Switches Covered By This Guide  
This document includes information on the following switches:  
Rapier 48w (DC model)  
Rapier 48w-B (AC and DC models)  
The Rapier 48w and 48w-B switches have the same features, however the  
physical connection between the switch and NSMs is different. The compatible  
NSMs for each model are:  
Rapier 48w: AT-AR040, AT-AR048  
Rapier 48w-B: AT-AR040-B, AT-AR048-B  
In this guide, the product name Rapier 48w refers to both the Rapier 48w and  
the Rapier 48w-B models, except where an explicit reference is made.  
You can download updates to this document from  
NEBS Compliance  
The Rapier 48w DC models meet Network Equipment Building System (NEBS)  
compliance under the following conditions:  
The switch is located in a network telecommunications facility.  
When rack-mounted, all bare conductors are coated with an appropriate  
antioxidant compound before making crimp connections.  
The supplied air filters are installed in both fan units.  
For information about NEBS requirements when connecting cables to the  
switch, see “Connecting Data Cables to the Switch” on page 14.  
The Rapier 48w AC model has not been tested for NEBS requirements.  
4
 
 
Installation and Safety Guide  
Package Contents  
These items are included with each Rapier 48w switch. Contact your authorised  
distributor or reseller if any items are damaged or missing.  
AC model package contents  
one serial cable for connecting the switch to a terminal or PC  
one AC power cord  
two 19inch rack-mount brackets, two 23inch rack-mount brackets and eight  
M4 flat head screws, for mounting the switch in a rack  
this Installation and Safety Guide  
one CD-ROM with complete documentation and utilities  
one warranty card  
DC model package contents  
one serial cable for connecting the switch to a terminal or PC  
two 19inch rack-mount brackets, two 23inch rack-mount brackets and eight  
M4 flat head screws, for mounting the switch in a rack  
one grounding stud crimp terminal  
two M5 hex nuts with lock washers for connecting the switch to primary  
ground  
one 4-terminal DC connector plug (MSTB) with fixing screws  
two air filters  
this Installation and Safety Guide  
one CD-ROM with complete documentation and utilities  
one warranty card  
5
 
 
Rapier 48w Switch  
Selecting a Site  
Before you install the switch, review the following considerations about its  
location.  
The Rapier 48w switch requires an ambient temperature from 0ºC to 50ºC  
(32ºF to 122ºF).  
There should be adequate front-to-back airflow around the switch and its  
vents.  
The site should be dust-free and without moisture.  
Humidity can be from 5% to 80% non-condensing.  
You need a reliable and earthed (grounded) power supply source, preferably  
dedicated and filtered.  
The switch ports are suitable for connection to intra-building or non-  
exposed cabling only (NEBS requirement)  
Cabling must not be exposed to sources of electrical noise, such as radio  
transmitters, broadband amplifiers, power lines, electric motors, and  
fluorescent fixtures.  
Related network devices can be connected to the switch but cannot exceed  
maximum cable lengths specified in the Hardware Reference.  
Ensure easy access to the switch’s power and cable connections.  
You may need to remove cabinet doors to accommodate cords and cables.  
When rack mounted, the switch must be located evenly to prevent uneven  
mechanical loading of the rack.  
Rapier 48w DC models are NEBS compatible only when the switch is  
located in a network telecommunications facility.  
6
 
 
Installation and Safety Guide  
Installing the Switch  
You can install the switch on a level surface, such as a desktop or bench, in a  
standard 19-inch rack, or in a 23-inch rack.  
The ports on the switch must not be metallically connected to interfaces that  
connect to Outside Plant or its wiring (NEBS requirement).  
Before you begin  
Read the safety information.  
For your well-being and that of the equipment, read the safety information in  
this document. You can also download this document from  
Verify the package contents if you have not already done so.  
See “Package Contents” on page 5. If any items are damaged or missing,  
contact your authorised distributor or reseller.  
Gather necessary tools and equipment.  
For a Rapier 48w AC switch, you will need:  
a Phillips #2 screwdriver for fitting the rack-mount brackets  
four rack-mount screws and cage nuts (if required)  
For a Rapier 48w DC switch, you will need:  
a Phillips #2 screwdriver for fitting the rack-mount brackets  
four rack-mount screws and cage nuts (if required)  
a flat screwdriver for the captive screws on the fan units and the DC  
power connection  
a suitable spanner for tightening the nuts on the chassis grounding stud  
an appropriate DC power source, DC supply cable, ring connectors,  
wire strippers, and a PANDUIT Uni-Die® dieless crimping toolset  
Prepare the cabinet in a suitable location  
Follow guidelines described in “Selecting a Site” on page 6 to choose an  
appropriate location and modify the rack as necessary.  
You can install the switch in a 19-inch rack, a 23-inch rack, or on a flat bench.  
If you have an optional Network Service Module (NSM), or Port Interface  
Cards (PICs), install them in the switch first.  
For details, refer to the Network Service Module Installation and Safety Guide and  
the Port Interface Card Installation and Safety Guide. These guides are shipped  
with each NSM or PIC. You can also download them from  
7
 
 
Rapier 48w Switch  
Rack-mount the switch  
1. Ensure the rack has sufficient space for the switch and its cables. For the  
switch’s requirements, see “Selecting a Site” on page 6.  
2. Install cage nuts, if required, so they are ready for the rack-mount screws in  
the following steps. The Rapier 48w can be front, center, or rear mounted.  
3. Unpack the switch.  
4. Screw one bracket to each side of the switch using the M4 screws provided.  
5. Mount the switch into the rack, and tighten the 4 rack-mount screws.  
8
 
Installation and Safety Guide  
Install the air filters (NEBS installation only)  
Rapier 48w DC switches are shipped with air filters that you must install in each  
of the fan units for Network Equipment Building System (NEBS) compliance.  
To install an air filter:  
1. Using a flat screwdriver, undo the captive screws on the front of the fan  
unit.  
2. Slide the fan unit out of its cage. The internal power connection is quite  
solid, so pull firmly on the captive screws.  
3. Insert the air filter into the narrow slot between the front grill of the fan  
unit and the fan. Position the air filter with the plastic frame towards the fan  
and the pull tab to the top. The air filter should fit snugly.  
4. Slide the fan unit back into its cage, making sure that the air filter and the  
pull tab are clear of any contact points.  
5. Press the fan unit firmly into place and tighten the captive screws on the  
front of the fan unit.  
9
 
Rapier 48w Switch  
Applying Power to the Switch  
The specific power supply requirements for the Rapier 48w are clearly displayed  
on the rear of the switch. If the supply is outside the accepted range for the  
switch, the switch may not operate or damage to the switch may result.  
Warning All versions of this equipment must be earthed.  
Rapier 48w AC switch  
Follow these instructions when powering the AC switch variant.  
1. Plug the provided AC power cord into the power inlet.  
2. Connect the power cord to the main power source.  
3. Check that the PSU LED on the front panel of the switch is lit green. If the  
LED does not light, refer to the Hardware Reference for troubleshooting  
information.  
48wAC_rear_panel  
10  
 
 
Installation and Safety Guide  
Rapier 48w DC switch  
Follow these instructions when connecting the DC switch variant. Read “Safety”  
on page 23 of this document before connecting a DC power supply.  
Warning Only trained and qualified personnel should connect a DC power  
supply.  
For centralised DC power connection, the switch should be installed in  
restricted access areas only (such as dedicated equipment rooms or  
equipment closets) in accordance with Articles 110-16, 110-17, and 110-18 of  
the National Electrical Code, ANSI/NFPA 70.  
Damage to equipment may result if power is connected improperly.  
Before working on equipment that is connected to power, remove jewellery  
including rings, necklaces, and watches. Metal objects will heat up when  
connected between power and ground, and can cause serious burns or weld the  
metal object to the terminals.  
NEBS preparation when rack-mounted  
To ensure rack-mounted installations are earthed for compatibility with NEBS,  
all bare conductors must be coated with an appropriate antioxidant compound  
before making crimp connections.  
DC supply cable and power supply  
Supply cable specifications:  
two-core cable is required  
2
minimum core size: 2.1mm (14 AWG)  
minimum cable rating: 600V, 90 degrees C  
Power supply specifications:  
48 VDC (40 to 60 VDC is acceptable)  
supports either positive grounded or negative grounded operation  
a 15Amp certified/listed circuit breaker is required for circuit protection  
11  
 
Rapier 48w Switch  
Connect the switch to ground  
The protective earth connection should be connected before proceeding with  
the following power connections. The primary ground for the equipment is a  
two stud grounding block (bearing the grounding symbol) located on the left  
rear of the chassis, adjacent to the DC power connector.  
To connect the switch to ground:  
2
1. Using a 10AWG (5mm cross sectional area) grounding cable (green with  
yellow stripe), connect the chassis grounding stud to the office primary  
ground using the two nuts with integral lock washers supplied. Tighten the  
nuts with an appropriate spanner.  
2. Strip an 18mm (0.75 inch) length of insulation from the grounding cable and  
connect this to the grounding stud crimp terminal, using PANDUIT Uni-  
Die® dieless crimping toolset. Ensure that no stranded wires protrude  
from the terminal. The torque value for the chassis grounding studs is 2.57  
Nm (22.8 lbf in).  
Connect the DC supplies  
To provide power supply resiliency, the Rapier 48w switch can receive its DC  
power from either of two separate sources. Each power source should supply  
48V DC (40 to 60VDC) to the switch. When the switch is powered by  
centralized DC power, use UL Listed Type TC tray cables to connect the  
equipment to the power sources. Each tray cable should have two conductors in  
2
the range #14 to #12 AWG (2.0 to 2.5mm cross sectional area), such as Belden  
No. 3081A.  
Each DC branch circuit should connect to the Rapier switch via a 15A  
(maximum) circuit breaker or fuse that meets the requirements for branch  
circuit protection. The DC supply should be fed via a circuit breaker or switch  
capable of disconnecting power during servicing. The tray cable should be a UL  
Listed Type TC tray cable with two conductors in the range #14 to #12 AWG  
2
(2.0 to 2.5mm cross sectional area), such as Belden No. 3081A.  
To connect the DC supply:  
1. Ensure that the DC power source is powered off during installation.  
2. Strip 12mm (0.5inches) of jacket material off the tray cable and strip 7mm  
(0.27inches) of insulation off each individual wire.  
12  
 
Installation and Safety Guide  
3. Connect the A feed -48V wire to the screw terminal labelled “A -” on the  
rear panel of the switch, and use a flat screwdriver to tighten the screw to  
a torque of 0.5 to 0.8Nm (4.4 to 7.1lbf in). Ensure no wire strands  
protrude from the terminal.  
WARNING  
This unit might have more  
than one power input. To  
reduce the risk of electric  
shock, disconnect all power  
inputs before servicing unit.  
FOR CENTRALIZED DC  
POWER CONNECTION,  
INSTALL ONLY IN  
A
40-60VDC  
4.5A MAX  
RESTRICTED AREA.  
DUAL INPUTS  
48wDC_rear_panel  
4. Connect the A feed 48V return wire to the screw terminal labelled “A +”  
on the rear panel of the switch, and use a flat screwdriver to tighten the  
screw to a torque of 0.5 to 0.8Nm (4.4 to 7.1lbf in). Ensure no wire  
strands protrude from the terminal. Note that the DC return input  
terminal must be connected as Isolated DC return (DC-I).  
5. Use the same procedure to connect an additional power source, if  
required, to the terminals labelled B.  
6. Secure the tray cable near the rack framework using multiple cable ties to  
minimize the chance of the connections being disturbed by casual contact  
with wiring. Use at least four cable ties separated 10cm (4inches) apart  
with the first one located within 15cm (6inches) of the terminal block.  
7. Energise the DC power source to the switch.  
The Fault LED should light for approximately 3 seconds as the switch runs  
internal tests. If the LED remains lit, refer to the Rapier Switch Hardware  
Reference for troubleshooting information.  
8. Check that the Power LED on the front panel lights green.  
If the LED fails to light, refer to the Rapier Switch Hardware Reference for  
troubleshooting information.  
13  
 
Rapier 48w Switch  
Connecting Data Cables to the Switch  
Once initial configuration is complete, connect the switch to the network.  
Warning The Ethernet, DS3, T1, and management/asyn ports of the equipment  
are suitable for connection to intra-building or unexposed wiring or cabling only.  
These ports must not be metallically connected to interfaces that connect to  
the OSP or its wiring. These interfaces are designed for use as intra-building  
interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE, Issue 4)  
and require isolation from the exposed OSP cabling. The addition of Primary  
Protectors is not sufficient protection in order to connect these interfaces  
metallically to OSP wiring.  
The management/asyn intra-building ports can only be directly connected to  
equipment within the same frame, cabinet or line-up and where the equipment is  
separated by a distance of 6m or less. The exception to this is when intra-  
building wiring (cabling) is used for maintenance purposes only and is not  
connected during normal operation.  
Ethernet 10/100Mbps RJ-45 ports  
Use either straight-through or cross-over twisted pair cables to connect  
network devices to the 10/100MB switch ports. The switch will autonegotiate  
the MDI/MDI-X polarity. Make sure that each cable connection is secure. The  
switch will now perform basic Layer 2 switching functions. By default, all switch  
ports are members of vlan1.  
Gigabit SFP ports  
SFP ports 49 and 50 support optional gigabit copper and fibre SFP (Small Form-  
factor Pluggable) transceivers. For a list of supported SFPs, see the Rapier Series  
Switch Hardware Reference.  
Warning Do not look into the optical ports of SFP cables or transceivers.  
Invisible laser radiation may be emitted from disconnected fibres or connectors.  
14  
 
 
Installation and Safety Guide  
The SFP transceiver must be inserted the right way in the slot:  
To install an SFP in port 49 (upper), the release lever hinge must be at  
the bottom.  
To install an SFP in port 50 (lower), the release lever hinge must be at  
the top.  
SFP Transceiver  
Release Lever  
48w_SFP  
To insert an SFP transceiver, slide the transceiver into the SFP socket, and firmly  
press it until it engages. To remove an SFP transceiver, first release it by gently  
pulling the release lever, then pull it out of the socket. Never force a transceiver  
into or out of a socket.  
WAN ports  
If you have installed an NSM, connect the NSM ports to the WAN. For more  
information, see the Network Service Module Installation and Safety Guide and the  
Network Service Module Hardware Reference.  
If you have installed an AR040 or AR040-B 4-PIC NSM with PICs, connect the  
PIC ports to the WAN. For more information, see the Port Interface Card  
Installation and Safety Guide and the Port Interface Card Hardware Reference.  
15  
 
Rapier 48w Switch  
Configuring the Switch  
The Rapier 48w switch can be configured with the Command Line Interface  
(CLI). Before configuring the switch, you must make some basic connections  
explained in the following procedure. Before starting the procedure, ensure that  
the switch is installed and operating.  
Using the CLI to configure the switch  
1. Connect a terminal or PC to a console port.  
The Rapier 48w has two identical asynchronous serial RS-232 console  
ports with DB9 connectors on the front panel, asyn0 and asyn1. Using the  
supplied RS-232 straight-through cable, connect your terminal or PC to  
one of the console ports. For NEBS compatibility, the cable must be  
shielded and grounded at both ends, especially if permanently connected.  
2. Set the communication parameters.  
Set the communication parameters on your terminal or terminal emulation  
program to:  
Bit rate: 9600  
Data bits: 8  
Parity: None  
Stop bits: 1  
Flow control: Hardware  
For information about terminal emulation, see Using Windows Terminal and  
HyperTerminal in the Hardware Reference.  
3. Log in at the prompt.  
After the switch has booted, the login prompt appears. If the login prompt  
does not appear, press the [Enter] key two or three times.  
When the switch boots for the first time, it automatically creates an  
account with manager privileges. The login name for the account is manager  
and the password is friend.  
At the login prompt, enter the login name and password as follows:  
Login: manager  
Password: friend  
The command prompt is displayed after successful login. You can now use  
the CLI to configure the switch.  
16  
 
 
Installation and Safety Guide  
4. Change the password.  
Change the password as soon as possible because a manager account with  
the default password is a serious security risk. Remember the new  
password because there is no way to retrieve it if you forget it.  
To change the account password, use the set password command.  
5. Configure the online help.  
To use online help you must first configure the help file, by using the  
command:  
set help=<filename>.hlp  
Help files have a .hlp extension. To see a list of help files loaded on your  
switch, use the command:  
show files=*.hlp  
6. Configure the switch.  
Refer to the Software Reference for more information about configuring  
the software. Alternatively, if you do not know the command syntax, use  
any of the following to help you:  
To display a list of help topics, use the help command.  
To display help on a specific topic, use the help <topic> command.  
To display a list of valid options, type a question mark or press the Tab  
key at the end of a partial command.  
To complete a parameter after you have typed enough letters to  
uniquely match the desired one, press the Tab key.  
7. Save the configuration.  
Save your configuration to a new file by using the command:  
create config=<filename>.cfg  
Then set the switch to load this file when it restarts by using the command:  
set config=<filename>.cfg  
17  
 
Rapier 48w Switch  
Checking LEDs  
The following tables describe how the switch and expansion modules report  
faults and operational activities. Expansion modules are optional and must be  
purchased separately. Contact your authorised Allied Telesis distributer or  
reseller, or visit www.alliedtelesis.com for more information on purchasing  
expansion modules.  
Status LEDs  
LED  
State  
Off  
Description  
FAULT  
Switch operation is normal.  
Red  
The switch or management software is  
malfunctioning.  
1 flash  
Green  
A switch fan has failed.  
POWER  
The switch is receiving power and the  
voltage is within the acceptable range.  
Off  
The switch is not receiving power.  
NSM LEDs  
LED  
State  
Description  
SWAP  
Green  
The NSM and its PICs are ready to be hot  
swapped.  
Off  
The Hot Swap button must be pressed  
before the NSM or its PICs can be hot  
swapped, or the software version does not  
support hot swapping.  
IN USE  
Green  
Off  
The NSM is installed, is receiving power and  
is operational. The NSM and its PICs are  
NOT ready to be hot swapped.  
No NSM is installed, or the NSM is not  
installed correctly (the switch unit has not  
recognised the NSM.  
18  
 
 
Installation and Safety Guide  
RJ-45 Port LEDs (Ports 1- 48)  
LED  
State  
Green  
Flashing  
Amber  
Flashing  
Off  
Description  
L/A  
100 M Link established  
100 M Link activity  
10 M Link established  
10 M Link activity  
No link  
D/C  
Green  
Flashing  
Amber  
Flashing  
Off  
Full Duplex  
N/A  
Half Duplex  
Collisions  
No link  
SFP Port LEDs (Ports 49 - 50)  
LED  
State  
Green  
Flashing  
Off  
Description  
L/A  
1000 M Link established.  
1000 M Link activity.  
No link.  
SFP  
Amber  
Flashing  
SFP installed.  
SFP installed, but indicating a transmission  
fault.  
Off  
No link.  
19  
 
Rapier 48w Switch  
Documentation Set  
The complete document set for Rapier Series switches includes the following:  
This Installation and Safety Guide for the Rapier 48w switch  
The Rapier 48w Switch Removable Fan Installation Guide, which describes how  
to install AT-FAN04 fan-only modules (FOMs) in the Rapier 48w switch  
The Rapier i Series Switch Safety and Statutory Information booklet, which  
contains safety information for all Rapier switches except the Rapier 48w  
The Rapier Series Switch Quick Install Guide, which describes how to install all  
Rapier switches except the Rapier 48w  
The Rapier Series Switch Hardware Reference, which contains detailed  
information on the hardware features of all Rapier Series switches  
The Rapier Series Switch AlliedWare™Operating System Software Reference, which  
contains detailed information on configuring the switch and its software  
The Network Service Module Installation and Safety Guide, which describes how  
to install a Network Service Module  
The Network Service Module Hardware Reference, which contains detailed  
information on the hardware features of Network Service Modules  
The Port Interface Card Installation and Safety Guide, which describes how to  
install a Port Interface Card  
The Port Interface Card Hardware Reference, which contains detailed  
information on the hardware features of Port Interface Cards  
The Uplink Module Installation and Safety Guide, which describes how to install  
an uplink module  
The Uplink Module Hardware Reference, which contains detailed information  
on the hardware features of uplink modules  
You can download these documents and updates from  
You need Adobe® Acrobat® Reader® to view, search, or print these  
documents. You can download it from www.adobe.com.  
The Documentation Tools CD-ROM included with each Rapier 48w switch  
contains these documents, plus:  
AT-TFTP Server for Windows, for transferring files to and from the switch  
Supported MIBs  
How-To Notes, Microsoft® Visio® stencils and other resources  
20  
 
 
Installation and Safety Guide  
AC Model Standards  
The Rapier 48w-B AC switch meets the following standards:  
Category  
Approval Agency and Requirement  
Electrical Safety  
UL60950-1  
CAN/CSA-C22.2 No. 60950-1-03  
EN60950-1  
AS/NZS 60950.1  
EN 60825-1  
21 CFR 1040  
Electromagnetic Compliance  
FCC CFR47 Part 15 Class A  
EN55022 Class A  
VCCI Class A  
AS/NZS CISPR22 Class A  
EN61000-3-2/3  
EN55024  
WEEE  
RoHS  
Meets requirements of Directive 2002/96/EC of  
the European Parliament and of the council of 27  
January 2003  
Meets requirements of Directive 2002/96/EC of  
the European Parliament and of the council of 27  
January 2003  
U.S. Federal Communications Commission  
RADIATED ENERGY  
Note: This equipment has been tested and found to comply with the limits for a Class  
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference when the equipment is  
operated in a commercial environment. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with this  
instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference  
in which case the user will be required to correct the interference at his own expense.  
Note: Modifications or changes not expressly approved by the manufacturer or the  
FCC can void your right to operate this equipment.  
Canadian Department of Communications  
This Class A digital apparatus meets all requirements of the Canadian Interference-  
Causing Equipment Regulations.  
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur  
le matériel brouilleur du Canada.  
21  
 
 
Rapier 48w Switch  
DC Model Standards  
The DC models of the Rapier 48w and 48w-B switches meet the following  
standards:  
Category  
Approval Agency and Requirement  
Electrical Safety  
UL60950-1  
CAN/CSA-C22.2 No. 60950-1-03  
21 CFR 1040  
EN60950-1  
AS/NZS 60950.1  
EN60825-1  
Electromagnetic Compliance  
NEBS Level 3  
FCC CFR47 Part 15 Class A  
GR-1089-Core Issue 4  
GR-63-Core Issue 3  
WEEE  
RoHS  
Meets requirements of Directive 2002/96/EC of  
the European Parliament and of the council of 27  
January 2003  
Meets requirements of Directive 2002/96/EC of  
the European Parliament and of the council of 27  
January 2003  
U.S. Federal Communications Commission  
RADIATED ENERGY  
Note: This equipment has been tested and found to comply with the limits for a Class  
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference when the equipment is  
operated in a commercial environment. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with this  
instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference  
in which case the user will be required to correct the interference at his own expense.  
Note: Modifications or changes not expressly approved by the manufacturer or the  
FCC can void your right to operate this equipment.  
Canadian Department of Communications  
This Class A digital apparatus meets all requirements of the Canadian Interference-  
Causing Equipment Regulations.  
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur  
le matériel brouilleur du Canada.  
22  
 
 
Installation and Safety Guide  
Safety  
WARNING: In a domestic environment this product may cause radio  
interference in which case the user may be required to take adequate measures.  
WARNING: Class 1 Laser product.  
WARNING: Do not stare into the laser beam.  
CAUTION: Use of controls or adjustments of performance or procedures  
other than those specified herein may result in hazardous radiation exposure.  
ELECTRICAL NOTICES  
WARNING: ELECTRIC SHOCK HAZARD  
To prevent ELECTRIC shock, do not remove the cover. No user-serviceable  
parts inside. This unit contains HAZARDOUS VOLTAGES and should only be  
opened by a trained and qualified technician.  
LIGHTNING DANGER  
DANGER: DO NOT WORK on equipment or CABLES during periods of  
LIGHTNING ACTIVITY.  
CAUTION: POWER CORD IS USED AS A DISCONNECTION DEVICE. TO  
DE-ENERGIZE EQUIPMENT, disconnect the power cord.  
ELECTRICAL - TYPE CLASS 1 EQUIPMENT  
THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a  
properly wired earth ground socket outlet. An improperly wired socket outlet  
could place hazardous voltages on accessible metal parts.  
PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the  
equipment and shall be easily accessible.  
CAUTION: Air vents must not be blocked and must have free access to the  
room ambient air for cooling.  
OPERATING TEMPERATURE: This product is designed for a maximum  
ambient temperature of 50 degrees C.  
ELECTRICAL - AC MAINS CIRCUIT OVERLOADING  
When installing product, consideration must be given to the accumulative  
nameplate ratings when connecting the equipment to the AC supply wiring.  
CAUTION: MECHANICAL LOADING - Mounting of the equipment in the  
rack should be such that a hazardous condition is not achieved due to uneven  
loading.  
Lithium Battery - Should only be changed by authorised service personnel.  
CAUTION: Danger of explosion if battery incorrectly replaced. Replace only  
with Lithium Battery, type CR2032, and dispose of in accordance with the  
manufacturer’s recommendations and all local codes.  
23  
 
 
Rapier 48w Switch  
ALL COUNTRIES: Install product in accordance with local and National  
Electrical Codes.  
WARNING: For centralized DC power connection, install only in a restricted  
access area.  
WARNING: Only trained and qualified personnel are allowed to install or  
replace this equipment.  
WARNING: As a safety precaution, a 15 Amp circuit breaker should be  
installed at the supply end of the cable to be used with this LAN equipment.  
Always connect the wiring to the LAN equipment first before connecting the  
wiring to the breaker. To avoid the danger of physical injury from electrical  
shock, do not work with HOT feeds. Always be sure that the breaker is in the  
Off position before connecting the wiring to the breaker.  
WARNING: Do not strip more than the recommended amount of wire.  
Stripping more than the recommended amount can create a safety hazard by  
leaving exposed wire on the terminal block after installation.  
WARNING: When installing this equipment, always ensure that the frame  
ground connection is installed first and disconnected last.  
WARNING: “Safety Hazard” - Check to see if there are any exposed  
copper strands coming from the installed wires. When this installation is done  
correctly, there should be no exposed copper wire strands extending from the  
terminal block. Any exposed wiring can conduct harmful levels of electricity to  
persons touching the wires.  
DC versions of this system will work with a positive grounded or negative  
grounded DC system.  
Sicherheit  
WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen  
hervorrufen. In diesem Fall müßte der Anwender angemessene  
Gegenmaßnahmen ergreifen.  
WARNUNG Laserprodukt der Klasse 1.  
WARNUNG Nicht direkt in den Strahl blicken.  
ACHTUNG: GEFÄHRLICHE SPANNUNG  
Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren  
Teile. Das Gerät steht unter Hochspannung und darf nur von qualifiziertem  
technischem Personal geöffnet werden.  
24  
 
 
Installation and Safety Guide  
GEFAHR DURCH BLITZSCHLAG  
GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines  
Gewitters ausführen.  
VORSICHT: DAS NETZKABEL DIENT ZUM TRENNEN DER  
STROMVERSORGUNG. ZUR TRENNUNG VOM NETZ, KABEL AUS DER  
STECKDOSE ZIEHEN.  
GERÄTE DER KLASSE 1  
DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer  
vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein  
unvorschriftsmäßiger Anschluß kann die Metallteile des Gehauses unter  
gefährliche elektrische Spannungen setzen.  
STECKBARES GERÄT: Die Anschlußbuchse sollte in der Nähe der Einrichtung  
angebracht werden und leicht zugänglich sein.”  
VORSICHT  
Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen  
freien Zugang zur Raumluft haben.  
BETRIEBSTEMPERATUR: Dieses Produkt wurde für den Betrieb in einer  
Umgebungstemperatur von nicht mehr als 50° C entworfen.  
NETZSICHERUNG  
Bei der Installation muß der auf dem Typenschild angezeigte Nennwert des  
Gerätes für den Anschluß an das Netz beachtet werden.  
VORSICHT: RAHMENEINBAU  
Die Geräte müssen so in den Rahmen montiert werden, daß keine Gefahren  
durch unebenen inbau des Rahmens verursacht werden.  
Lithium-Batterie - Sollte nur von einem geschulten qualifizierten Techniker  
ausgetauscht werden.  
VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie.  
Nur mit einer gleichen Batterie oder einem gleichwertigen Batterietyp nach  
Empfehlung des Herstellers ersetzen. Gebrauchte Batterien nach Anweisungen  
des Herstellers beseitigen.  
ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen  
Vorschriften entsprechen.  
Warnung: Bei zentralisierten gleichstromverbindungen sollte die installation  
nur an einem standort mit beschränktem zugang erfolgen.  
Warnung: INSTALLATION UND WARTUNG DIESER EINRICHTUNG NUR  
DURCH AUSGEBILDETES FACHPERSONAL.  
Warnung: Aus Sicherheitsgründen sollte am Netzteilende des mit dieser LAN-  
Einrichtung verwendeten Kabels ein 15-Ampere-Leistungsschalter installiert  
werden.  
25  
 
Rapier 48w Switch  
Nehmen Sie STETS zuerst die Verkabelung der LAN-Einrichtung vor, bevor Sie  
die Kabel an den Leistungsschalter anschließen. Arbeiten Sie nie mit  
SPANNUNGSFÜHRENDEN Kabeln, um Körperverletzungen durch  
Stromschlag zu vermeiden. Achten Sie stets darauf, daß sich der  
Leistungsschalter in der Position Off (Aus) befindet, bevor Sie Kabel an den  
Leistungsschalter anschließen.  
Warnung: Ziehen Sie nicht mehr als die empfohlene Drahtlänge ab. Wird mehr  
als die empfohlene Länge abisoliert, stellt dies ein Sicherheitsrisiko dar, da auf  
dem Anschlußklemmblock nach der Installation möglicherweise freiliegende  
Drähte verbleiben.  
Warnung: Bei der Installation dieser Einrichtung ist stets sicherzustellen, daß  
der Masseanschluß jeweils zuerst installiert und zuletzt getrennt wird.  
Warnung: “Sicherheitsrisiko” Prüfen Sie, daß aus dem installierten Draht  
keine freiliegenden Kupferlitzen herausragen. Bei korrekter Installation sollten  
aus dem Anschlußklemmblock keine freiliegenden Kupferlitzen vorstehen.  
Freiliegende Kabel führen genug Spannung, um Personen zu gefährden, die diese  
Drähte berühren.  
Hinweis: Dieses System kann mit positiv geerdeten oder negativ geerdeten  
Gleichstromsystemen betrieben werden.  
Sikkerhed  
ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio  
forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage  
tilstrækkelige foranstaltninger.  
ADVARSEL Laserprodukt av klasse 1.  
ADVARSEL Stirr ikke på strålen.  
ELEKTRISKE FORHOLDSREGLER  
ADVARSEL: RISIKO FOR ELEKTRISK STØD  
For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre  
dele, der kan repareres af brugeren. Denne enhed indeholder LIVSFARLIGE  
STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret tekniker.  
FARE UNDER UVEJR  
FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med  
LYNAKTIVITET.  
ADVARSEL: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE  
STRØMMEN. SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen  
ud af stikket.  
26  
 
 
Installation and Safety Guide  
ELEKTRISK - KLASSE 1-UDSTYR  
DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet  
med en korrekt installeret jordforbunden stikkontakt. En ukorrekt installeret  
stikkontakt kan sætte livsfarlig spænding til tilgængelige metaldele.  
UDSTYR TIL STIKKONTAKT, stikkontakten bør installeres nær ved udstyret og  
skal være lettilgængelig.  
ADVARSEL: Ventilationsåbninger må ikke blokeres og skal have fri adgang til  
den omgivende luft i rummet for afkøling.  
BETJENINGSTEMPERATUR: Dette apparat er konstrueret til en  
omgivende temperatur på maksimum 50 grader C.  
ELEKTRISK-OVERBELASTNING AF SPÆNDINGSKREDSLØBET  
Ved installation af produktet, bør der tages hensyn til den kumulative kapacitet  
der angives på navneskiltet, når udstyret forbindes med vekselstrømsledningen.  
ADVARSEL: MEKANISK OPSTILLING-Udstyret skal opstilles i stativet, på en  
sådan måde, at der kke opstår fare p.g.a. ujævn opstilling.  
Lithium batteri - Bør kun udskiftes af uddannet og kvalificeret tekniker.  
ADVARSEL : Eksplosionsfare, hvis batteriet udskiftes ukorrekt. Udskift kun  
med samme eller en tilsvarende type der anbefales af producenten. Kassér  
brugte batterier i overensstemmelse med producentens instruktioner.  
ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal  
og national lovgivning for elektriske installationer.  
Advarsel: ETABLERES FORBINDELSEN TIL ET JÆVNSTRØMSNET, BØR  
INSTALLERING FORETAGES I ET OMRÅDE HVOR UVEDKOMMENDE IKKE  
HAR ADGANG.  
Advarsel: INSTALLERING OG UDSKIFTNING AF DETTE UDSTYR BØR  
KUN UDFØRES AF AUT. EL-INSTALLATØR.  
Advarsel: Der bør indskydes en 15 A automatsikring på forsyningsenden af  
kablet til dette LAN-udstyr.  
Man skal ALTID først forbinde ledningerne med LAN-udstyret inden de  
forbindes med automatsikringen. Ved ledningsarbejde skal strømmen altid være  
AFBRUDT til forebyggelse af fare for elektrisk stød. Man skal altid SLUKKE  
automatsikringen inden man forbinder ledninger med den.  
Advarsel: Man bør ikke afisolere mere af ledningerne end anvist, for så kan  
sådanne blanke ledninger udgøre et faremoment efter montering på  
klemmerækken.  
Advarsel: Ved installering af dette udstyr skal steljord altid forbindes først og  
aftages sidst.  
27  
 
Rapier 48w Switch  
Advarsel: “Fare” Se omhyggeligt efter om der stikker blanke kobbertråde ud  
fra klemmeforbindelserne. Ved korrekt montering er det ikke tilfældet. Enhver  
afisoleret leder kan lede farlig strømstyrke til personer, som kommer til at røre  
ved dem.  
Bemærk: Dette udstyr kan køre både på jævnstrøm med positiv og med  
negativ jord.  
Veiligheid  
WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken,  
in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te  
nemen.  
WAARSHUWING Klasse-1 laser produkt.  
WAARCHUWING Neit in de straal staren.  
WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT  
WAARSCHUWING: GEVAAR VOOR ELEKTRISCHE SCHOKKEN  
Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen.  
Binnenin bevinden zich geen onderdelen die door de gebruiker onderhouden  
kunnen worden. Dit toestel staat onder GEVAARLIJKE SPANNING en mag  
alleen worden geopend door een daartoe opgeleide en bevoegde technicus.  
GEVAAR VOOR BLIKSEMINSLAG  
GEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.  
WAARSCHUWING: HET TOESTEL WORDT UITGESCHAKELD DOOR  
DE STROOMKABEL TE ONTKOPPELEN.OM HET TOESTEL STROOMLOOS  
TE MAKEN: de stroomkabel ontkoppelen.  
ELEKTRISCHE TOESTELLEN VAN KLASSE 1  
DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn  
op een juist geaarde contactdoos. Een onjuist geaarde contactdoos kan de  
metalen onderdelen waarmee de gebruiker eventueel in aanraking komt onder  
gevaarlijke spanning stellen.  
AAN TE SLUITEN APPARATUUR, de contactdoos wordt in de nabijheid van de  
apparatuur geïnstalleerd en is gemakkelijk te bereiken.”  
OPGELET: De ventilatiegaten mogen niet worden gesperd en moeten de  
omgevingslucht ongehinderd toelaten voor afkoeling.  
BEDRIJFSTEMPERATUUR: De omgevingstemperatuur voor dit produkt  
mag niet meer bedragen dan 50 graden Celsius.  
28  
 
 
Installation and Safety Guide  
ELEKTRISCH: OVERBELASTING VAN WISSELSTROOM HOOFDCIRCUIT  
Tijdens de installatie van het produkt dient men rekening te houden met de  
gecombineerde waarden op de naamplaatjes bij het aansluiten van het toestel op  
de wisselstroom-voedingsdraden.  
OPGELET: MECHANISCH LADEN - De montage van het toestel in het rek  
dient zo uitgevoerd te worden dat geen gevaar ontstaat door een ongelijke  
lading.  
Lithium batterij. Mag alleen worden vervangen door een daartoe opgeleide en  
bevoegde technicus.  
OPGELET: Gevaar voor ontploffing indien de batterij verkeerd wordt  
vergangen. Alleen vervangen door hetzelfde of een gelijkwaardig, door de  
fabrikant aanbevolen type.  
ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale  
elektrische voorschriften.  
Waarschuwing: BIJ GECENTRALISEERDE DC-AANSLUITING: INSTALLATIE  
UITSLUITEND UITVOEREN IN EEN GEBIED MET BEPERKTE TOEGANG.  
Waarschuwing: ALLEEN GESCHOOLD EN GEKWALIFICEERD PERSONEEL  
MAG DEZE APPARATUUR INSTALLEREN OF VERVANGEN.  
Waarschuwing: Op de kabel die op de LAN-apparatuur wordt aangesloten  
dient een zekering van 15 amp te worden gemonteerd aan de zijde van de  
aansluiting op de voeding.  
Sluit bedrading ALTIJD eerst op de LAN-apparatuur aan en pas daarna op de  
zekering. Voorkom het risico op een elektrische schok en schakel eerst de  
voeding uit. Controleer voordat u de bedrading op de zekering aansluit altijd of  
de zekering zich in de stand UIT bevindt.  
Waarschuwing: Verwijder niet meer dan de aanbevolen hoeveelheid  
isolatiemateriaal. Als u meer dan de aanbevolen hoeveelheid verwijdert, kan dit  
een veiligheidsrisico veroorzaken doordat draden bloot blijven liggen na  
aansluiting op het blok.  
Waarschuwing: Zorg er tijdens installatie van de apparatuur altijd voor dat de  
aardeaansluiting van het frame als eerste wordt geplaatst en als laatste wordt  
losgemaakt.  
Waarschuwing: “Veiligheidsrisico” Controleer of er bij de aangesloten  
bedrading geen koper blootligt. Als de installatie juist is uitgevoerd, is er bij het  
aansluitblok geen koperdraad zichtbaar. Blootliggende bedrading kan schadelijke  
elektriciteitsniveaus geleiden naar personen die met de draden in aanraking  
komen.  
Opmerking: Dit systeem werkt met positief geaarde of negatief geaarde DC-  
systemen.  
29  
 
Rapier 48w Switch  
Sécurité  
MISE EN GARDE : dans un environnement domestique, ce produit peut  
provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra  
prendre les mesures adéquates.  
ATTENTION Producit laser di classe 1.  
ATTENTION Ne pas fixer le faisceau des yeux.  
INFORMATION SUR LES RISQUES ÉLECTRIQUES  
AVERTISSEMENT: DANGER D’ÉLECTROCUTION  
Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement protecteur du  
matériel. Ce matériel ne contient aucun élément réparable par l’utilisateur. Il  
comprend des TENSIONS DANGEREUSES et ne doit être ouvert que par un  
technicien dûment qualifié.  
DANGER DE FOUDRE  
DANGER: NE PAS MANIER le matériel ou les CÂBLES lors d’activité  
orageuse.  
ATTENTION: LE CORDON D’ALIMENTATION SERT DE MISE HORS  
CIRCUIT. POUR COUPER L’ALIMENTATION DU MATÉRIEL, débrancher le  
cordon.  
ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE  
CE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La prise de courant doit être  
branchée dans une prise femelle correctement mise à la terre car des tensions  
dangereuses risqueraient d’atteindre les pièces métalliques accessibles à  
l’utilisateur.  
EQUIPEMENT POUR BRANCHEMENT ELECTRIQUE, la prise de sortie doit  
être placée près de l’équipement et facilement accessible”.  
ATTENTION: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air  
ambiant de circuler librement pour le refroidissement.  
TEMPÉRATURE DE FONCTIONNEMENT: Ce matériel est capable de  
tolérer une température ambiante maximum de ou 50 degrés Celsius.  
SURCHARGE DES CIRCUITS PRINCIPAUX DE COURANT ALTERNATIF  
ÉLECTRIQUE  
Lors de l'installation du matériel, il faut prendre en compte la somme des  
puissances indiquées sur les étiquettes au moment de connecter le matériel à  
une source de courant alternatif.  
ATTENTION : RÉPARTITION DE LA CHARGE MÉCANIQUE - Le montage  
du matériel dans le bâti doit être effectué de telle manière que la répartition de  
la charge mécanique ne pose aucun danger.  
30  
 
 
Installation and Safety Guide  
Pile en Lithium-Doit uniquement être remplacée par un technicien dûment  
qualifié  
ATTENTION : Un danger d'explosion existe en cas de remplacement  
incorrect de la pile. Remplacer uniquement avec une pile du même type ou d'un  
type recommandé par le fabricant. Mettre au rebut lespiles usagées  
conformément aux instructions du fabricant).  
POUR TOUS PAYS: Installer le matériel conformément aux normes  
électriques nationales et locales.  
Avertissement: POUR UNE CONNEXION A UNE SOURCE  
D’ALIMENTATION C.C. CENTRALISEE, L’INSTALLATION DOIT ETRE  
UNIQUEMENT EFFECTUEE DANS UNE ZONE D’ACCES LIMITE.  
Avertissement: SEUL UN PERSONNEL QUALIFIE ET ENTRAINE EST  
AUTORISE A INSTALLER OU REMPLACER CET EQUIPEMENT.  
Avertissement: Par mesure de sécurité, un disjoncteur de 15 A doit être  
installé au point d’alimentation électrique du câble devant être utilisé avec cet  
équipement de réseau local (LAN).  
Connectez TOUJOURS le câblage à l’équipement LAN avant de le connecter  
au disjoncteur. Pour éviter tout risque de blessure corporelle par électrocution,  
ne travaillez pas lorsque le matériel est sous tension. Assurez-vous toujours que  
le disjoncteur est bien en position d’ARRET avant de le connecter au câblage.  
Avertissement: Ne coupez pas une quantité de câble supérieure à celle qui est  
recommandée. Cela pourrait constituer un risque de sécurité en laissant du  
câblage à nu sur le bornier après l’installation.  
Avertissement: Lors de l’installation de cet équipement, vérifiez toujours que  
la connexion de terre du châssis est installée en premier et débranchée en  
dernier.  
Avertissement: “Risque de sécurité” Vérifiez qu’aucun fil de cuivre dénudé  
ne sort du câble installé. Lorsque cette installation est effectuée correctement,  
aucun fil de cuivre ne devrait dépasser du bornier. Tout câblage dénudé peut être  
conducteur de tensions dangereuses pour les personnes touchant les câbles.  
Remarque: Ce système peut fonctionner avec des systèmes C.C. dotés d’une  
mise à la terre positive ou négative.  
31  
 
Rapier 48w Switch  
Turvallisuus  
VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä,  
missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin  
toimenpiteisiin.  
VAROITUS Luokan 1 Lasertuote.  
VAROITUS Älä katso säteeseen.  
SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA  
VAROITUS: SÄHKÖISKUVAARA  
Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa  
olevia osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain  
koulutettu ja pätevä teknikko.  
SALAMANISKUVAARA  
HENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN  
KANSSA SALAMOINNIN AIKANA.  
HUOMAUTUS: VIRTAJOHTOA KÄYTETÄÄN  
VIRRANKATKAISULAITTEENA. VIRTA KATKAISTAAN irrottamalla virtajohto.  
SÄHKÖ - TYYPPILUOKAN 1 LAITTEET  
TÄMÄ LAITE TÄYTYY MAADOITTAA. Pistoke täytyy liittää kunnollisesti  
maadoitettuun pistorasiaan. Virheellisesti johdotettu pistorasia voi altistaa  
metalliosat vaarallisille jännitteille.  
PISTORASIAAN KYTKETTÄVÄ LAITE; pistorasia on asennettava laitteen lähelle  
ja siihen on oltava esteetön pääsy.”  
HUOMAUTUS: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys  
ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi.  
KÄYTTÖLÄMPÖTILA: Tämä tuote on suunniteltu ympäröivän ilman  
maksimilämpötilalle 50°C.  
SÄHKÖ-VAIHTORVIRTASÄHKÖPIIRIN YLIKUORMITUS  
Tuotetta asennettaessa on otettava huomioon osien nimikilvissä osoitettu teho  
silloin kun osat liitetetään vaihtovirtaverkkoon.  
HUOMAUTUS: MEKAANINEN KUORMITUS--Osien asennuksen alustaan  
tulee tapahtua siten, että epätasainen kuormitus ei aiheuta vaaraa.  
Litiumparisto - Vaihdon voi suorittaa vain koulutettu ja pätevä teknikko.  
Varoitus: Räjähdysvaara, jos paristo on vaihdettu väärin. Vaihda vain samaan tai  
vastaavaan tyyppiin, jota valmistaja suosittelee. Hävitä käytetyt paristot  
valmistajan ohjeiden mukaan.  
KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten  
sähköturvallisuusmääräysten mukaisesti.  
32  
 
 
Installation and Safety Guide  
Varoitus: KESKITETTY TASAVIRTAKYTKENTÄ ASENNETTAVA  
AINOASTAAN TILAAN, JOHON ON RAJOITETTU PÄÄSY.  
Varoitus: TÄMÄN LAITTEEN SAA ASENTAA TAI VAIHTAA AINOASTAAN  
KOULUTETTU JA AMMATTITAITOINEN HENKILÖKUNTA.  
Varoitus: Tämän LAN-laitteen kanssa käytettävän kaapelin syöttöpäähän tulee  
turvallisuussyistä asentaa 15 A virrankatkaisin.  
Yhdistä johdot AINA ensin LAN-laitteeseen ennen virrankatkaisimeen  
kytkemistä. Sähköiskusta johtuvien vammojen välttämiseksi älä käsittele  
JÄNNITTEELLISIÄ johtoja. Varmista aina, että virrankatkaisin on pois päältä (off)  
ennen kuin yhdistät johdot katkaisimeen.  
Varoitus: Älä poista johtimesta päällystettä enempää kuin on suositeltu.  
Päällysteen poistaminen suositusta pidemmältä matkalta voi aiheuttaa  
turvallisuusriskin, sillä riviliittimeen jää asennuksen jälkeen paljaita johtimia.  
Varoitus: Kun asennat tätä laitetta, varmista aina, että runkomaadoitettu liitin  
kytketään ensin ja irrotetaan viimeiseksi.  
Varoitus: Turvallisuusriski Tarkista, ettei asennetusta johtimesta näy paljaita  
kuparisäikeitä. Kun asennus suoritetaan oikein, riviliittimestä ei pitäisi näkyä  
paljaita kuparijohdinsäikeitä. Paljaat johtimet voivat aiheuttaa sähköiskuvaaran,  
jos niihin kosketaan.  
Huomaa: Tämä järjestelmä toimii positiivisesti tai negatiivisesti maadoitettujen  
tasavirtajärjestelmien kanssa.  
Norme di Sicurezza  
AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare  
radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli  
adeguati provvedimenti.  
AVVERTENZA Prodotto laser di Classe 1.  
AVERTENZA Non fissare il raggio con gli occhi.  
AVVERTENZE ELETTRICHE  
ATTENZIONE: PERICOLO DI SCOSSE ELETTRICHE  
Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti  
interne non sono riparabili dall’utente. Questa unità ha TENSIONI  
PERICOLOSE e va aperta solamente da un tecnico specializzato e qualificato.  
PERICOLO DI FULMINI  
PERICOLO: NON LAVORARE sul dispositivo o sui CAVI durante  
PRECIPITAZIONI TEMPORALESCHE.  
33  
 
 
Rapier 48w Switch  
ATTENZIONE: IL CAVO DI ALIMENTAZIONE È USATO COME  
DISPOSITIVO DI DISATTIVAZIONE. PER TOGLIERE LA CORRENTE AL  
DISPOSITIVO staccare il cavo di alimentazione.  
ELETTRICITÀ - DISPOSITIVI DI CLASSE 1  
QUESTO DISPOSITIVO DEVE AVERE LA MESSA A TERRA. La spina deve  
essere inserita in una presa di corrente specificamente dotata di messa a terra.  
Una presa non cablata in maniera corretta rischia di scaricare una tensione  
pericolosa su parti metalliche accessibili.  
APPARECCHIATURA COLLEGABILE, la presa va installata vicino  
all’apparecchio per risultare facilmente accessibile”.  
ATTENZIONE: le prese d’aria non vanno ostruite e devono consentire il  
libero ricircolo dell’aria ambiente per il raffreddamento.  
TEMPERATURA DI FUNZIONAMENTO: Questo prodotto è concepito  
per una temperatura ambientale massima di 50 gradi centigradi.  
ELETTRICITÀ - SOVRACCARICO DEL CIRCUITO DI RETE A C.A.  
Durante l'installazione ed il collegamento del dispositivo alla rete di  
alimentazione a corrente alternata, è necessario tenere in considerazione le  
capacità cumulative riportate sulla targhetta.  
ATTENZIONE: CARICAMENTO MECCANICO - Il montaggio del dispositivo  
sul supporto va effettuato in maniera tale da evitare qualsiasi potenziale  
condizione di pericolo eventualmente dovuta al montaggio irregolare.  
Batteria al litio - Va sostituita solo da un tecnico specializzato e qualificato.  
ATTENZIONE: l'errata sostituzione della batteria può causare pericolo di  
esplosioni. Sostituire solamente con lo stesso tipo o con uno equivalente  
raccomandato dal produttore. Eliminare le batterie usate secondo le istruzioni  
del produttore.  
TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative  
elettriche nazionali.  
Avvertenza: AI FINI DEL COLLEGAMENTO CENTRALIZZATO DI  
ALIMENTAZIONE A CC, INSTALLARE SOLO IN UN’AREA AD ACCESSO  
LIMITATO.  
Avvertenza: L’INSTALLAZIONE E LA SOSTITUZIONE DI QUESTA  
APPARECCHIATURA DEVONO ESSERE EFFETTUATE SOLAMENTE DA  
PERSONALE SPECIALIZZATO E QUALIFICATO.  
Avvertenza: A titolo di cautelativo, installare un interruttore di sicurezza da 15  
ampere sull’estremità in entrata del cavo di alimentazione di questa  
apparecchiatura LAN.  
Collegare SEMPRE il cablaggio prima all’apparecchiatura LAN e poi  
all’interruttore. Per evitare i infortuni causati da folgorazione, non lavorare su  
34  
 
Installation and Safety Guide  
cavi SOTTO TENSIONE. Prima di collegare il cavo all’interruttore di sicurezza,  
accertarsi sempre che quest’ultimo sia disinserito.  
Avvertenza: Per evitare i possibili pericoli associati all’esposizione dei fili sulla  
morsettiera dopo l’installazione, non rimuovere l’isolamento oltre le misure  
specificate.  
Avvertenza: Quando si installa questo apparecchio, accertarsi sempre che il  
collegamento a massa del telaio sia sempre il primo ad essere effettuato e  
l’ultimo ad essere scollegato.  
Avvertenza: “Pericolo!” Controllare che il filo installato non abbia trefoli in  
rame esposti. Se l’installazione è stata effettuata in modo corretto, non vi deve  
protrudere dalla morsettiere alcun trefolo in rame esposto. In caso di contatto,  
un filo esposto può condurre livelli di elettricità pericolosi a quanti lo tocchino.  
Nota: Questo sistema funziona con sistemi a CC con massa positiva o negativa.  
Sikkerhet  
ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet  
forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige  
forholdsregler.  
ADVARSEL Laserprodukt av klasse 1.  
ADVARSAL Stirr ikke på strålen.  
ELEKTRISITET  
ADVARSEL: FARE FOR ELEKTRISK SJOKK  
For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som  
brukeren kan reparere på innsiden. Denne enheten inneholder FARLIGE  
SPENNINGER, og må kun åpnes av en faglig kvalifisert tekniker.  
FARE FOR LYNNEDSLAG  
FARE: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.  
FORSIKTIG: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET.  
FOR Å DEAKTIVISERE UTSTYRET, må strømforsyningen kobles fra.  
ELEKTRISK - TYPE 1- KLASSE UTSTYR  
DETTE UTSTYRET MÅ JORDES. Strømkontakten må være tilkoplet en korrekt  
jordet kontakt. En kontakt som ikke er korrekt jordet kan føre til farlig  
spenninger i lett t ilgjengelige metalldeler.  
UTSTYR FOR STIKKONTAKT. Stikkontakten skal monteres i nærheten av  
utstyret og skal være lett tilgjengelig.”  
FORSIKTIG: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med  
romtemperatur for avkjøling.  
35  
 
 
Rapier 48w Switch  
DRIFTSTEMPERATUR: Dette produktet er konstruert for bruk i maksimum  
romtemperatur på 50 grader celsius.  
ELEKTRISK OVERBELASTNING PÅ AC HOVEDKRETSLØP  
Når produktet installeres, må de samlede navneplateverdiene kontrolleres nøye  
når strøm påsettes.  
FORSIKTIG: MEKANISK LASTNING Installering av utstyret på hyllen må  
utføres på en slik måte at ingen farlige situasjoner oppstår som en følge av ujevn  
lastning.  
Litiumbatteri — Må kun byttes ut av en faglig kvalifisert tekniker.  
FORSIKTIG: Eksplosjonsfare hvis batteriet feilinnsettes.Batteriet må bare  
erstattes med samme type eller en tilsvarende type som er anbefalt av  
fabrikanten. Batteriene må kasseres i samsvar med fabrikantens instruksjoner.  
ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale  
elektriske koder.  
Advarsel: VED TILKOPLING TIL ET LIKESTRØMSNETT, SKAL DU BARE  
MONTERE UTSTYRET PÅ ET STED HVOR UVEDKOMNE IKKE HAR  
ADGANG.  
Advarsel: DETTE UTSTYRET SKAL BARE MONTERES ELLER SKIFTES UT AV  
KVALIFISERT PERSONELL SOM HAR GJENNOMGÅTT OPPLÆRING.  
Advarsel: Av sikkerhetshensyn bør en automatsikring på 15 A monteres i  
forsyningsenden av kabelen som skal brukes sammen med dette LAN-utstyret.  
Du skal ALLTID først kople ledningene til LAN-utstyret før du kopler ledningene  
til automatsikringen. Arbeid aldri med ledninger uten at strømmen er slått av,  
ettersom det ellers kan være fare for personskader som følge av elektrisk støt.  
Pass alltid på at automatsikringer er slått AV før du kopler ledningene til  
automatsikringen.  
Advarsel: Du skal ikke avisolere mer av ledningen enn det som er anbefalt.  
Dersom du avisolerer mer enn det som er anbefalt, kan dette forårsake en  
sikkerhetsfare, ettersom det vil finnes uisolert ledning på rekkeklemmen etter  
montering.  
Advarsel: Når du monterer dette utstyret, skal du alltid passe på at  
forbindelsen til rammejordingen monteres først og koples fra sist.  
Advarsel: “Sikkerhetsfare” Kontroller om uisolerte koppertråder stikker ut  
av den monterte ledningen. Hvis monteringen er riktig utført, skal det ikke  
finnes uisolerte kobbertråder som stikker ut fra rekkeklemmen. Uisolerte  
ledninger kan lede skadelige mengder strøm til personer som berører  
ledningene.  
Merknad: Systemet fungerer med positivt og negativt jordede  
likestrømssystemer.  
36  
 
Installation and Safety Guide  
Segurança  
AVISO: Num ambiente doméstico este produto pode causar interferência na  
radiorrecepção e, neste caso, pode ser necessário que o utente tome as  
medidas adequadas.  
AVISO Produto laser de classe 1  
AVISO Não olhe fixamente para o raio.  
AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS  
ATENÇÃO: PERIGO DE CHOQUE ELÉTRICO  
Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que  
possam ser consertadas pelo usuário. Este aparelho contém VOLTAGENS  
PERIGOSAS e só deve ser aberto por um técnico qualificado e treinado.  
PERIGO DE CHOQUE CAUSADO POR RAIO  
PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos  
suscetíveis a QUEDAS DE RAIO.  
CUIDADO: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM  
DISPOSITIVO DE DESCONEXÃO. PARA DESELETRIFICAR O  
EQUIPAMENTO, desconecte o cabo de ALIMENTAÇÃO.  
ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1  
DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQUIPAMENTO. O  
plugue de alimentação deve ser conectado a uma tomada com adequada ligação  
de fio terra. Tomadas sem adequada ligação de fio terra podem transmitir  
voltagens perigosas a peças metálicas expostas.  
EQUIPAMENTO DE LIGAÇÃO, a tomada eléctrica deve estar instalada perto  
do equipamento e ser de fácil acesso.”  
CUIDADO: As aberturas de ventilação não devem ser bloqueadas e devem ter  
acesso livre ao ar ambiente para arrefecimento adequado do aparelho.  
TEMPERATURA DE FUNCIONAMENTO: Este produto foi projetado  
para uma temperatura ambiente máxima de 50 graus centígrados.  
ELÉTRICO - SOBRECARGA DA REDE DE CORRENTE ALTERNADA (AC)  
Antes de instalar o produto, verifique o efeito cumulativo da conexão de  
diversos aparelhos àrede de corrente alternada através das etiquetas que  
indicam potência ou amperagem.  
CUIDADO: CARREGAMENTO - O equipamento deverá ser montado no  
suporte de montagem de forma tal que não cause perigo devido a carregamento  
não uniforme.  
37  
 
 
Rapier 48w Switch  
Bateria de lítio - Só deve ser trocada por técnico qualificado e treinado.  
CUIDADO: Se a bateria não for devidamente instalada há perigo de explosão.  
Substitua somente pelo mesmo tipo ou equivalente, conforme recomendado  
pelo fabricante. Descarte baterias usadas, de acordo com as instruções  
fornecidas pelo fabricante.  
TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e  
locais para instalações elétricas.  
Aviso: PARA UMA LIGAÇÃO CC CENTRALIZADA, INSTALE APENAS  
NUMA ZONA DE ACESSO RESTRITO.  
Aviso: SÓ PESSOAL TREINADO E QUALIFICADO PODE INSTALAR OU  
SUBSTITUIR ESTE EQUIPAMENTO.  
Aviso: Como medida de precaução, deve instalar-se um disjuntor de 15 Amp na  
extremidade de alimentação do cabo a ser usado com este equipamento LAN.  
Ligue SEMPRE os cabos ao equipamento LAN primeiro antes de os ligar ao  
disjuntor. Para evitar o perigo de ferimentos por choque eléctrico, não trabalhe  
com alimentadores LIGADOS. Verifique sempre se o disjuntor está na posição  
OFF (desligado) antes de ligar os cabos ao mesmo.  
Aviso: Não corte mais fio do que recomendado. Cortar mais do que o  
recomendado pode ser perigoso, por deixar fio exposto no terminal depois da  
instalação.  
Aviso: Ao ligar este equipamento, instale sempre primeiro a ligação à terra e  
desligue-a sempre em último.  
Aviso: “Perigo” Verifique se há algum fio de cobre exposto a sair do fio  
instalado. Quando esta instalação é feita correctamente não deve haver qualquer  
fio de cobre exposto a sair do terminal. Qualquer fio exposto pode conduzir  
níveis perigosos de electricidade para a pessoa que toque nos fios.  
Nota: Este sistema funciona com sistemas CC com ligações à terra Positivas ou  
Negativas.  
38  
 
Installation and Safety Guide  
Seguridad  
ADVERTENCIA: en un entorno doméstico, este producto puede causar  
radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las  
medidas que sean convenientes al respecto.  
¡ADVERTENCIA! Producto láser Clase 1.  
¡ADVERTENCIA! No mirat fijamente el haz.  
AVISOS ELECTRICOS  
ADVERTENCIA: PELIGRO DE ELECTROCHOQUE  
Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún  
componente en el interior al cual puede prestar servicio el usuario. Esta unidad  
contiene VOLTAJES PELIGROSOS y sólo deberá abrirla un técnico entrenado y  
calificado.  
PELIGRO DE RAYOS  
PELIGRO: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en  
los equipos o en LOS CABLES durante TORMENTAS ELECTRICAS.  
ATENCION: EL CABLE DE ALIMENTACION SE USA COMO UN  
DISPOSITIVO DE DESCONEXION. PARA DESACTIVAR EL EQUIPO,  
desconecte el cable de alimentación.  
ELECTRICO - EQUIPO DEL TIPO CLASE 1  
ESTE EQUIPO TIENE QUE TENER CONEXION A TIERRA. El cable tiene que  
conectarse a un enchufe a tierra debidamente instalado. Un enchufe que no está  
correctamente instalado podría ocasionar tensiones peligrosas en las partes  
metálicas que están expuestas.  
EQUIPO CONECTABLE, el tomacorriente se debe instalar cerca del equipo, en  
un lugar con acceso fácil”.  
ATENCION: Las aberturas para ventilación no deberán bloquearse y deberán  
tener acceso libre al aire ambiental de la sala para su enfriamiento.  
TEMPERATURA REQUERIDA PARA LA OPERACIÓN: Este producto  
está diseñado para una temperatura ambiental máxima de 50 grados C.  
ELECTRICO - SOBRECARGA DEL CIRCUITO PRIMARIO DE CORRIENTE  
ALTERNA  
Al instalarse el producto deberán considerarse las potencias nominales  
acumulativas, cuando se conecta el equipo al cable de alimentación de corriente  
alterna.  
ATENCION: CARGA MECANICA - El montaje del equipo en el bastidor debe  
realizarse de manera tal que no cause una condición peligrosa debido a la  
distribución desigual del peso.  
39  
 
 
Rapier 48w Switch  
Batería de litio - Sólo deberá ser cambiada por un técnico entrenado y calificado.  
ATENCION: Peligro de explosión si la batería no se reemplaza en forma  
correcta. Reemplace sólo con el mismo tipo o equivalente que recomienda el  
fabricante. Deseche las baterías usadas según las instrucciones del fabricante.  
PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los  
Códigos Eléctricos locales y nacionales.  
Advertencia: PARA HACER CONEXIONES DE CC CENTRALIZADAS,  
INSTALE EL CONMUTADOR ÚNICAMENTE EN LUGARES CON ACCESO  
RESTRINGIDO.  
Advertencia: ÚNICAMENTE EMPLEADOS CAPACITADOS Y  
COMPETENTES TIENEN LA AUTORIZACIÓN DE INSTALAR O REPONER  
DICHO EQUIPO.  
Advertencia: Por razones de precaución, se debe instalar un cortacircuitos de  
15 amperios en el extremo de alimentación del cable que se utilizará con este  
equipo LAN.  
SIEMPRE conecte los cables al equipo LAN primero, antes de conectarlos al  
cortacircuitos. Para evitar el peligro de sufrir daños corporales a causa de  
sacudidas eléctricas, no trabaje con conductores CON CORRIENTE. Asegúrese  
siempre de que el cortacircuitos esté en la posición de APAGADO (OFF) antes  
de conectar los cables al cortacircuitos.  
Advertencia: No pele el cable más de la cantidad recomendada, ya que si  
después de instalar el bloque terminal quedan cables pelados, habrá riesgos de  
seguridad.  
Advertencia: Cuando instale dicho equipo, asegúrese siempre de que el  
bastidor se conecte a tierra primero y se desconecte por último.  
Advertencia: “Riesgo de seguridad” Cerciórese de que no haya hilos de  
cobre pelados que salgan del alambre instalado. Cuando dicha instalación se  
realiza correctamente, los hilos de cobre pelados no deben salir del bloque  
terminal. Todo alambre pelado puede conducir niveles de electricidad nocivos a  
la persona que lo toca.  
Nota: Este sistema funcionará con sistemas de CC con conexión positiva o  
negativa a tierra.  
40  
 
Installation and Safety Guide  
Säkerhet  
VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket  
kan tvinga användaren till att vidtaga erforderliga åtgärder.  
VARNING! Laserprodukt av klass 1.  
VARNING! Laserstrålning när enheten är öppen.  
TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK:  
RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket.  
Det finns inga delar inuti som behöver underhållas. Denna apparat är under  
HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker.  
FARA FÖR BLIXTNEDSLAG  
FARA: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.  
VARNING: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT  
KOPPLA FRÅN STRÖMMEN, dra ur nätkabeln.  
ELEKTRISKT - TYP KLASS 1 UTRUSTNING  
DENNA UTRUSTNING MÅSTE VARA JORDAD. Nätkabeln måste vara  
ansluten till ett ordentligt jordat uttag. Ett felaktigt uttag kan göra att närliggande  
metalldelar utsätts för högspänning. Apparaten skall anslutas till jordat uttag, när  
den ansluts till ett nätverk.  
UTRUSTNING MED PLUGG. Uttaget skall installeras i utrustningens närhet och  
vara lättåtkomligt”.  
VARNING: Luftventilerna får ej blockeras och måste ha fri tillgång till  
omgivande rumsluft för avsvalning.  
DRIFTSTEMPERATUR: Denna produkt är konstruerad för rumstemperatur  
ej överstigande 50 grader Celsius.  
ELEKTRISKT - ÖVERBELASTNING AV VÄXELSTRÖMSNÄTET: När  
produkten installeras bör den sammanlagda effekten på namnplåten beaktas när  
apparaten ansluts till växelströmsnätet.  
VARNING: MEKANISK BELASTNING: Utrustningen ska installeras i chassit på  
så sätt att fara inte uppstår p g a ojämn belastning.  
Litium batteri - Får endast bytas av utbildade och kvalificerade tekniker.  
VARNING: Risk för explosion om felaktigt batteri används. Byt endast mot  
samma eller likvärdig typ batteri, rekommenderat av tillverkaren. Kassera  
använda batterier i enlighet med tillverkarens instruktioner.  
ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga  
bestämmelser för elektrisk utrustning.  
Varning: ANSLUTNING TILL LIKSTRÖMSNÄT FÅR ENDAST SKE I LOKAL  
DÄR OBEHÖRIGA EJ ÄGER TILLTRÄDE.  
41  
 
 
Rapier 48w Switch  
Varning: INSTALLATION OCH UTBYTE AV DENNA UTRUSTNING FÅR  
ENDAST UTFÖRAS AV AUKTORISERAD ELINSTALLATÖR.  
Varning: Av säkerhetsskäl skall en 15 A automatsäkring anslutas till  
försörjningsänden på kabeln som används till denna LAN-utrustning.  
Ledningar skall ALLTID anslutas till LAN-utrustningen innan ledningarna ansluts  
till automatsäkringen. För att förebygga uppkomsten av personskador orsakade  
av elektrisk stöt skall man inte vidröra strömförande uttag. Kontrollera alltid att  
automatsäkringen är i läget OFF (AV) innan anslutning av ledningar till  
automatsäkringen sker.  
Varning: Skala inte av mer isolering än vad som anges ovan. Skalas för mycket  
isolering av kan fara uppstå om oskyddad tråd vidröras på anslutningsplinten  
efter anslutningen.  
Varning: Vid anslutning av denna utrustning skall man alltid se till att jordtråden  
ansluts först och lossas sist.  
Varning: OBS! FARA! Kontrollera om små koppartrådar sticker ut ifrån den  
anslutna tråden. Om anslutningen utförts riktigt sticker inga trådar ut från  
anslutningsplinten. Oisolerade trådar kan överföra skadlig elektricitet till person  
som vidrör trådarna.  
Anmärkning: Detta system fungerar både med positivt och negativt jordade  
likströmskällor.  
Telecommunications Interfaces  
The following statements apply to Network Service Module (NSM) and Port  
Interface Card (PIC) expansion options for Wide Area Network (WAN) links.  
Warning To reduce risk of fire use only No.26 awg or larger  
telecommunications line cord if the cord supplied is not used with the apparatus.  
Important Safety Instructions  
When using your telephone equipment, basic safety precautions should always  
be followed to reduce the risk of fire, electric shock and injury to persons,  
including the following:  
1. Do not use this product near water, for example near a bathtub, washbowl,  
kitchen sink, or laundry tub in a wet basement or near a swimming pool.  
2. Avoid using a telephone (other than a cordless type) during an electrical  
storm. There may be remote risk of electric shock from lightning.  
3. Do not use the telephone to report a gas leak in the vicinity of the leak.  
42  
 
 
Installation and Safety Guide  
4. Use only the power cord and batteries indicated in this manual. Do not  
dispose of batteries in a fire. They may explode. Check with local codes for  
possible special disposal instructions.  
5. Remove the telephone cord from the unit prior to making changes to the  
expansion port.  
Save these instructions  
Connection to ISDN network  
Ports for the connection of other apparatus  
The following interfaces normally operate at SELV (Safe Extra Low Voltage)  
levels:  
Asynchronous (console) ports  
Ethernet ports  
G703 ports  
Synchronous ports  
Note SELV is a secondary circuit whose voltages do not exceed a safe value  
under normal operating conditions and under single fault conditions. Under  
normal operating conditions the voltages do not exceed 42.4 V peak AC or  
60 V DC.  
TNV1  
The following interfaces are Telecommunications Network Voltage (TNV1)  
circuits, which operate normally within the limits of SELV:  
BRI ports for connection to ISDN Basic Rate telecommunications networks  
PRI ports for connection to ISDN Primary Rate telecommunications  
networks  
E1/T1 ports for connection to E1/T1 services  
Note A TNV1 circuit is a circuit which under normal operating conditions does  
not exceed the limits for SELV and on which overvoltages from  
telecommunication networks are possible.  
43  
 
Rapier 48w Switch  
US Federal Communications Commission (FCC)  
This equipment complies with Part 68 of the Federal Communications  
Commission (FCC) rules for the United States.  
A label is located on the underside of the base unit containing the FCC  
registration number. You must, upon request, provide the following information  
to your local telephone company:  
For the AR021U PIC  
Facility Interface Code  
Service Order Code  
021S5  
6.0Y  
The AR021U PIC has completed the ISDN  
Ordering Codes Translation Review and is  
registered for IOC S and EZ-ISDN 1.  
RJ49C  
USOC Jack Type  
Should you experience trouble with this telephone equipment, please contact:  
Allied Telesis, Inc.  
19800 North Creek Parkway, Suite 200  
Bothell WA, 98011  
Phone: 1 800 424 6596  
Fax: 1 425 481 3895  
If trouble is experienced with this equipment (AR021U PIC), for repair or  
warranty information, please contact the above. If the equipment is causing harm  
to the telephone network, the telephone company may request that you  
disconnect the equipment until the problem is resolved.  
This equipment cannot be used on public coin phone service provided by the  
telephone company. Connection to party line service is subject to state tariffs.  
Your telephone company may discontinue your service if your equipment causes  
harm to the telephone network. They will notify you in advance of  
disconnection, if possible. During notification, you will be informed of your right  
to file a complaint to the FCC.  
Occasionally, your telephone company may make changes in its facilities,  
equipment, operation, or procedures that could affect the operation of your  
equipment. If so, you will be given advance notice of the change to give you an  
opportunity to maintain uninterrupted service.  
44  
 
Installation and Safety Guide  
Canadian Department of Communications  
The Industry Canada label identifies certified equipment. This certification  
means that the equipment meets telecommunications network protective,  
operational and safety requirements as prescribed in the appropriate Terminal  
Equipment Technical Requirements document(s). The Department does not  
guarantee the equipment will operate to the user’s satisfaction.  
Before installing this equipment, users should ensure that it is permissible to be  
connected to the facilities of the local telecommunications company. The  
equipment must also be installed using an acceptable method of connection. The  
customer should be aware that compliance with the above conditions may not  
prevent degradation of service in some situations.  
Repairs to certified equipment should be coordinated by a representative  
designated by the supplier. Any repairs or alterations made by the user to this  
equipment, or equipment malfunctions, may give the telecommunications  
company cause to request the user to disconnect the equipment.  
Users should ensure for their own protection that the electrical ground  
connections of the power utility, telephone lines and internal metallic water pipe  
system, if present, are connected together. This precaution may be particularly  
important in rural areas.  
Warning Users should not attempt to make such connections themselves, but  
should contact the appropriate electric inspection authority, or electrician, as  
appropriate.  
This digital apparatus does not exceed the limits for radio noise emissions from  
digital apparatus as set out in the Radio Interface Regulations of the Canadian  
Department of Communications.  
Le present appareil numerique n’emet pas de bruits radioelectriques depassant  
les limites applicables aux appareils numeriques prescrites dans le Reglement sur  
le brouillage radioelectrique edicte par le ministere des Communications du  
Canada.  
45  
 

321 Studios Coffeemaker ITG Trunk 20 User Manual
ABC Office Paper Shredder 4107 User Manual
Agilent Technologies Water Heater E4350B User Manual
AG Neovo Flat Panel Television H 19 User Manual
Agri Fab Log Splitter 25 0126 User Manual
American Standard Plumbing Product 7430801 User Manual
Atlantic Indoor Furnishings 050202 User Manual
Audiovox Car Satellite Radio System CNP2000UC User Manual
Barco Camera Accessories R9864220 User Manual
Beko Refrigerator CXFD5104 W User Manual